Crown CTS 600USP3CN

Crown CTS 600USP3CN

Crown CTS 600USP3CN Description:

The Crown CTs-600 is a 2-Channel power amplifier housed in a 2-space rackmount frame, offering power levels and features meant to serve fixed installation sound applications. This amplifier is notable for a completely independent array of switches and indicators for each channel, including high and low impedance operation, input sensitivity, high pass filters, and an advanced level of well designed overload protection circuitry. This unit includes a PIP-USP3 module for networked controlling via either HiQnet and System Architect or TCP/IQ and IQwic.

Crown CTS 600USP3CN Features:

• High-power, 2-channel, 2U rackmount amplifier for installed sound applications
• Switching power supply lowers overall amplifier weight
• Direct 70V/100V/140V/200V constant-voltage or 2/4/8 Ohm low-impedance operation
• Independently selectable Input Sensitivity switching per channel
• Rear panel Programmable Input Processor(PIP2) connector accepts accessory expansion modules for specific custom installation requirements
• Thermal Level Control(TLC) circuitry protects amplifier from overheating; engages input compressor, dynamically reducing input gain when individual channels overheat
• Junction Temperature Simulation(JTS) quick-activation circuitry limits drive level of output devices to tolerable range if excess power is required; protects output transistors without shutting down channel
• Continuously variable fan cooling; venting with front-to-rear forced airflow
• Removable balanced terminal block input connectors with "Y" switch
• Switchable high pass filter per channel, eliminates step down transformer saturation in distributed systems
• Complete array of front panel function and warning indicator LEDs for each channel
• Complete array of rear panel function and filter switches
• Power on indicator flashes when AC mains are under or over voltage
• Advanced protection circuitry covers shorted outputs, DC, mismatched loads, overheating, high frequency overloads, voltage fluctuation and internal faults.

Crown CTS 600USP3CN Specifications:

• Output Power 2 ohm Dual (Per Channel): 150W
• 4 ohm Dual (Per Channel): 300W
• 8 ohm Dual (Per Channel): 300W
• 16 ohm Dual (Per Channel): 300W
• 70V Dual (Per Channel): 300W
• 4 ohm Bridge: 300W
• 8 ohm Bridge: 600W
• 16 ohm Bridge: 600W
• 140V Bridge: 600W
• Damping Factor 10 Hz - 100 Hz:>3000
• Input Sensitivity Switchable:
• 1.4V(8/4 Ohms)
• 26 dB Gain:
• 2.46V(4 Ohm Load)
• 3.47V (8 Ohm Load)
• 1.4V(70V)
• Input Impedance 10 kOhms balanced(nominal), 5 kOhms unbalanced(nominal)
• Gain 35:1 (31 dB)
• Frequency Response 20 Hz - 20 kHz +/-0.25 dB @ 1 Watt
• Signal-to-Noise Ratio 105 dB A-Weighted, below rated power(20 Hz - 20 kHz)
• Total Harmonic Distortion (THD) < 0.1%, at full rated power (20 Hz - 20 kHz)
• Input Connections 2 x Balanced 3-Pin Terminal Block Connectors(one per channel)
• Output Connectors 1 x 4-Pole Terminal Strip(Ch 1, Ch 2)
• Controls Front Panel 1 x Power Switch
• Controls (Rear) 1 x Reset Switch
• 1 x Rotary Channel Level Control(per channel)
• 1 x 2-Position Operation Mode Switch
• 1 x Highpass Filter Switch(per channel)
• 1 x "Y" Input Switch
• 1 x Interior 3-Position Input Sensitivity Switch(per channel)
• Indicators Front Panel:
• 1 x Yellow LED Bridge Mode Indicator
• 1 x Green LED Ready Indicator
• 3 x Green LED Signal Indicators(per channel)
• 1 x Red LED Clip Indicator(per channel)
• 1 x Red LED Thermal Indicator(per channel)
• 1 x Red LED Fault Indicator
• 1 x Yellow LED Data Indicator(per channel)
• 1 x Blue LED Power Indicator
• Back Panel: No Indicators on Back Panel
• Cooling Continuously Variable Speed Fans
• Ventilation Grille(Front),Cooling Vents(Back)
• Front-to-Rear forced airflow
• Power Consumption 24 Watts (120 VAC Mains)
• Dimensions (WxHxD) 19 x 3.5 x 14.25" (483 x 89 x 362mm)
• Weight 22.8 lb (10.3 kg)
• Specialties Variable Speed Fan Cooling
• Thermal Level Control
• JTS Limiting Circuitry

Get your Crown 600USP3CN product today!